 |
AC
POWER SUPPLY / FREQUENCY CONVERTER
INVERTER
UNINTERRUPTIBLE
POWER SUPPLY (UPS)
MODIFIED
STANDARD PRODUCTS
RAILROAD
SIGNAL SOURCE
APPLICATION
NOTES MAGAZINE ARTICLES
WILD
FREQUENCY INFORMATION CENTER
N.I.
® LabView Drivers
|
 |
|
BL1350 AC
POWER SUPPLY
FREQUENCY CONVERTER / INVERTER
1350VA, AC
Power Supply / Frequency Converter / Inverter in a 3.5"H
Chassis
|
|
BL1350
|
|
Behlman's
BL1350 AC Power Supply / Frequency Converter / Inverter, requires
just 3.5" of rack
height,
and weighs as low as 45 pounds, yet it delivers 1350 VA of quality
AC power. In the BL 1350, you'll find the quality features you
expect from Behlman, fully adjustable frequency and voltage,
total harmonic distortion of less then 0.5%, high efficiency,
plus excellent line and load regulation.
There's
also a unique overload protection system that folds back the
voltage to maintain maximum rated current without output wave
form distortion and analog remote control. For rack mounted
or bench top power, no AC source combines small size, high efficiency
and low cost like the Behlman BL Series.
Features
-
1350VA
in a 3.5" chassis, some models under 45 pounds
-
Parallelable
for additional power or for 3 phase output
-
Unique overload
protection prevents output distortion
-
Remote DC programming
for voltage and frequency
-
True RMS readout
of voltage and current
-
Low cost without
compromising features or performance
|
Click
here for printable 
Specifications Sheet
| Specifications
|
|
INPUT
|
|
Voltage:
|
B-1
(115V), C-2 (115/230V +/-10%),
C-4
(120/208V, 3 phase, +/-10%)
|
Frequency:
|
47-63Hz
|
|
|
BL1350pf: 85-270V
|
|
47-63Hz
|
|
OUTPUT
|
|
Voltage:
|
0-135V
or 0-270V
Other
voltages available
|
Frequency:
|
45-500Hz (Optional
45-1000Hz)
|
|
Power:
|
1350VA, Units can
be stacked for increased power, or 2 or 3 phase output
|
current:
|
10 Amps, 0-135V
Range
5 Amps, 0-270V Range
|
|
Current Crest
Factor:
|
3:1
|
Line Regulation:
|
+/-0.1% for +/-10%
Line change
|
|
Distortion:
|
0.5% THD Typical
(measured at full load, 100 Volts, 50Hz)
|
Load Regulation:
|
+/-0.7% No load
to full load
|
|
Efficiency:
|
80% Typical
|
Power Factor:
|
100% of rated output
into any power factor load
|
|
PROTECTIVE CIRCUITS
|
|
Input Protection:
|
Fast acting main
circuit breaker
|
Thermal Protection:
|
Internal temperature
sensor prevents heat damage
|
|
Constant Current
Mode:
|
Overload automatically
causes voltage foldback to provide maximum current without distorting
output waveform
|
Short Circuit
Protection:
|
Short circuit overload
electronically latches output open to protect load. Power restored
by recycling circuit breaker
|
|
CONTROL INPUTS
|
|
Voltage/Frequency:
|
0-10Vdc programming-voltage/frequency
|
|
External Synch:
|
Synchronizes AC
output with external input
|
|
Optional:
|
IEEE488 or RS232
interface for remote programming and read back of output voltage
and frequency
|
|
Front Panel
Control
-
Power On/Off
circuit breaker
-
Output On/Off
toggle switch
-
Frequency and
amplitude control (optional locking controls)
-
Digital readout
(3.5 digits)-True RMS voltage/true RMS current/frequency
|
-
Range Switch
(dual voltage range models)
-
Three LED's:
Constant Current, Overload, OverTemp
-
Phase adjust
-
Three binding
posts
|
|
MECHANICAL &
ENVIRONMENTAL
|
|
Dimensions:
|
High strength 19"
(48.3 cm) rack mounted chassis, 3.5" high by 22"
deep (8.9 cm X 55.9 cm)
|
|
Weight:
|
BL1350B-1 &
Pf 45 lb, C-2 & C-4 70 lb
|
|
Output Connections:
|
Front panel binding
posts and rear mounted barrier strip
|
|
Operating Temperature:
|
32° to 131° F (0
to 55 degrees C)
|
|
MODEL SELECTION
GUIDE
|
|
Model
|
Input
Voltage
|
Output
Voltage
|
Dual
Range
|
Isolated
Output
|
|
BL1350B-1(1)
|
115VAC
|
0
- 135VAC
0 - 270VAC
|
Yes
|
No
|
|
BL1350C-2(1)
|
115/230VAC
|
0
-135VAC
0 - 270VAC
|
Yes
|
Yes
|
|
BL1350C-4(1)
|
120/208VAC,
3
phases
|
0
-135VAC
0 - 270VAC
|
Yes
|
Yes
|
|
BL1350pf
|
85-270VAC
|
0
- 135VAC
0 - 270VAC
|
Yes
|
Yes
|
|
MODEL OPTIONS
|
|
Options
|
Description
|
|
CE
|
CE mark available
on model C-2 & pf...for model pf, CE Mark for low voltage
directive (LVD) only
|
|
E
|
Extended frequency
range
|
|
L
|
Locking pots
|
|
T
|
Output: 0-150
or 0-300VAC
|
| T2 |
Output:
0-34 or 0-135 VAC |
|
S
|
Slides
|
|
B
|
Rubber Feet
|
|
A
|
Safety Sockets
|
|
I
|
IEEE-488 interface
|
|
IR
|
RS232 interface
|
| R |
Ruggedization |
|
|
Motor Test
|
|
J
|
Input: 100/200VAC
single phase
|
|
H
|
Cabinet enclosure
for 3 units
|
|
P
|
Parallel wiring
for 2 or 3 phases
|
| W |
Wiring
for 3 phase configuration |
|
Note:1:
Available
models with motor testing option add -MT (See below).
Contact
factory for additional options.
Please note that Option MT includes
all of the specifications of the standard BL Series plus the
following to features to meet the requirements for motor testing:
- Unique
overload protection prevents output distortion
- "Soft Start" allows
starting motors in "locked rotor" condition by
folding back the voltage and slowly increasing it as the
motor starts to accelerate.
- Capable of starting motors
which normally require 140Amps locked rotor starting currents.
- Capable of supplying a running
current up to 14 Amps at 50% duty cycle.
|
|
 |
 |
